It may be of advantage to operate testing instruments via separate keyboards. Therefore, DOLI offers several remote machine controls. They can be designed custom-made for OEM customers.

RMC - Remote machine control with
three keys and Digipoti

TAST - Remote machine control with 15 keys and Digipoti to be connected to 4TAST (without foil)

(01457)

The 4DI-Monitor has been developed to quickly solve problems with the communication between measurement electronics and testing instrument. He will be connected to the 4DI drive interface of the EDC.

• All incoming signals are represented by LEDs on the 4DI-Monitor, all kinds of switchs can be simulated.

• Using the "short-circuit-plug" - which in fact replaces the testing instrument - the signals of the EDC will be shown exclusively.

• The monitor can be connected between the EDC and the testing instrument, hence facilitating the trouble-shooting with the EDC as well as with the testing instrument.

The operative range of the 4DI-Monitor extends from the research&development over the production up to the service department.

(01725)

Complete container with base shell and top shell (with multiple socket, without cable conduit, without EDC). Removable Mounting plate with top head rails and cable channels for an easy mounting of contactors or power amplifiers etc. outside of the shell. Earthing bar for all metal shields. Strain relief clamp and earthing bar for shielded cables.

 (01520)

Fitting for strain gauges and inductive transducers (1.16 – 1,625V/V) and analog signals, 1ms detection rate, linearity 0,01%, accuracy 0,025%. The 4FAD fits for static and dynamic applications with a frequency of up to approx. 100Hz.

PDF-Download

(00725)

Fitting for strain gauges and inductive transducers (116 - 1625 mV/V) and analogue signals, A/D Conversion ±140.000 at 20ms integration time, linearity 0,01%, Accuracy 0,025%

PDF-Download

(01206)

Two incremental counters with digital quadruplication. The control adaptation happens via the sensor plug. The board offers 6 outputs with 24V/100mA, one output relay with change-over contact as well as 5 inputs with 24V-level.

(01239)

The board offers 6 outputs with 24V/100mA, one output relay with change-over contact as well as 5 inputs with 24V-level.

(01491)

±10V-output with a resolution of 16 bit. Application e.g. for Lo-approach with automatic strain transducers or clamping force control of hydraulic clamps.

(01398)

(00887)

Interface board either for the remote control TAST with 15 keys and Digipoti or for the plug/screw-terminal TERM with 22 outputs and 22 inputs especially for larger control tasks.

(01167)

I/O terminal with plug-in terminals for the application in e.g. instruments for the connection and poll of pneumatic valves etc.

(01148)

Additional board for 4DI for a high resolution of the output (±15 Bit) with ±10V signal. Digital set value interface for 10kHz to 2MHz adjustable in eight steps.

(00766)

Analog output for the EDC basic units, load channel (DC-supply) or for 4ETF and 4FAD boards. ANA supplies a ±10V signal, that will be decoupled after the filter. This signal is not scaled; and there are no possibilities to do so.

(01011)

Draw wire transducer, cable length 5m, sensor plug 9IL (0792) already written and mounted on it.

(01442)

With this option, up to 32 EDCs can be polled synchronuously. The SYNCH Option contains an interface board and the necessary connections for the installation inside the EDC. As this option has a serial RS485-bus, an EDC connecting cable (1336) as well as a bus closing device for the start and the end (1337, 1404) are necessary in addition.

(00706)

Remote Machine Control with the functions Up/Down/Stop and the Digital Potentiometer for the setup of the instrument. Magnetic housing, 2m cable.

(00888)

© 2005 DOLI Elektronik